IEC 60297 PDF

IEC 60297 PDF

IEC Dimensions of Mechanical Structures of the mm (19 in) Series Part 1: Panels and Racks. IEC Mechanical structures for electronic equipment – Dimensions of mechanical structures of the ,6 mm (19 in) series – Part Basic. IEC Dimensions of Mechanical Structures of the mm (19 Inch) Series Part 2: Cabinets and Pitches of Rack Structures.

Author: Kikasa Kigarn
Country: Seychelles
Language: English (Spanish)
Genre: Finance
Published (Last): 15 December 2004
Pages: 162
PDF File Size: 8.27 Mb
ePub File Size: 6.21 Mb
ISBN: 800-5-46421-392-3
Downloads: 90748
Price: Free* [*Free Regsitration Required]
Uploader: Nelrajas

Wikimedia Foundation servers as seen from the front. The isc pattern thus repeats every 1. Installation and removal of hardware in a square hole rack is very easy and boltless, where the weight of the equipment and small retention clips are all that is necessary to hold the equipment in place. These aisles may themselves be enclosed into a cold air containment tunnel so that cooling air does not travel to other parts of the building where it is not needed or mixes with hot air, making it less efficient.

These posts are typically heavy gauge metal or extruded aluminum. Thus, a 1U rackmount computer is not 1.

inch rack – Wikipedia

The size denotes the width of the faceplate for the installed equipment. The term relay rack appeared first in the world of telephony. Two-post racks are most often used for telecommunication installations. Production of clearance-hole racks is less expensive because tapping the holes is eliminated and replaced with fewer, less expensive, cage nuts.

Archived from the original on The earliest repeaters from were installed in ad-hoc fashion on shelves, in wooden boxes and cabinets. The holes are large enough to permit a bolt to be freely inserted through without binding, and bolts are fastened in place using cage nuts. The posts have holes in them at regular intervals, 6297 both posts matching, so that each hole is part of a horizontal pair with a center-to-center distance of Although open-frame racks are the least expensive, they also expose air-cooled equipment to dust, lint, and other environmental contamination.

  ALAIN BADIOU METAPOLITICS PDF

By using this site, you agree to the Terms of Use and Privacy Policy. Larger cases typically have wheels for easy transport. The shape of small cases is maintained by the rack rails and the cover seal extrusions alone.

Computer enclosure Mechanical standards Server hardware. As a result, 4-post lec have become common, with such racks featuring a mirrored pair of rear mounting posts.

This gap allows a bit of room above and below an installed piece of equipment so it may be removed without binding on the adjacent equipment. When rack rails are too thin to tap, rivnuts or other threaded inserts can be used, and when the particular class of equipment to be mounted is known in advance, some of the holes can be omitted from the mounting rails.

The rack unit is a measure of vertical spacing and is common to both the 19 and 23 inch racks.

19-inch rack

A blade server enclosure 62097 require 10U. The posts are each 0. Two-post racks provide two vertical posts. The cases typically use extruded aluminum bands at the ends of the body with tongue-and-groove mating to like bands for the covers.

According to Telcordia Technologies Generic Requirements document GRCORE, during an earthquake, telecommunications equipment is subjected to motions that can over-stress equipment framework, circuit boards, and connectors. A difficulty with forced air fan cooling in rack equipment is that fans can fail due to age or dust.

  EL INFIERNO DE MARTA PASQUAL ALAPONT PDF

However, some rack equipment has been designed to make fan replacement easy, using quick-change fan trays that can be accessed without removing the cabling or the device from the rack, and in some cases without turning off the device so that operation is uninterrupted during replacement.

The fans themselves can be difficult to replace.

To protect equipment from shock and vibration road rack cases use an inner and ie case. This of course varies by manufacturer, the design of the rack and its purpose, but through common constraining factors such as raised floor tile dimensionsthese dimensions have become quite ic. When there is a large number of computers in a single rack, it is impractical for each one to have its own separate keyboard, mouse, and monitor.

Occasionally, one may see fractional U devices such as a 1. However, not all equipment is suitable for this type of mounting. Rack-mountable equipment is traditionally mounted by bolting or clipping its front 6097 to the rack.

Older equipment meant for round-hole or tapped-hole racks can still be used, with the use of cage nuts made for square-hole racks. The outer shell is frequently embossed in a self-mating pattern to combat the tendency for stacked cases to deform slightly creating a slope that encourages the upper case to slide off. See also Industrial PC. The distance of the right edge of the oec mounting rail to the left edge of the left mounting rail is millimetres