BC558 TRANSISTOR DATASHEET PDF

BC558 TRANSISTOR DATASHEET PDF

DataSheet: PDF icon BCPDF. BC is a general purpose PNP transistor. It is used in switching and amplifier applications. The DC current gain varies in. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. Semiconductor data sheets and/or specifications can and do vary in different applications . BC / BC / BC VCE = -5 V, IC = µA.

Author: Voodootaxe Kihn
Country: Jordan
Language: English (Spanish)
Genre: Medical
Published (Last): 14 November 2007
Pages: 96
PDF File Size: 10.32 Mb
ePub File Size: 3.51 Mb
ISBN: 583-1-75339-212-6
Downloads: 6715
Price: Free* [*Free Regsitration Required]
Uploader: Nak

The BC because of this large gain value is normally used to as a audio amplifier. Interface GPS with Arduino. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched. Choosing Battery for Robots. Complete Transistro Details can be found in the BC datasheet given at the end of this page.

As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin. What is Web Browser. It is also used as a complement for transistors BC to BC It can amplify power, voltage and current at different configurations.

Interface SD Card with Arduino. TL — Programmable Reference Voltage. SPI Module of Arduino. This is known as the biasing. Choosing Motor For Robots. The voltage divider is the commonly used biasing mode. In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal.

  IPC 2221A FILETYPE PDF

The value of this resistor RB can be calculated using below formulae. For amplification applications, transistoor transistor is biased such that it is partly on for all input conditions.

A Transistors acts as an Amplifier when operating in Active Region.

BC558 Datasheet, Equivalent, Cross Reference Search

When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter. BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at dstasheet and will be opened Reverse biased when a signal is provided to base pin.

In the absence of base signal, it gets completely off.

This high-density System-in-Package SiP integrates controller, power switches, and support components. Virgin Galactic — Commercial Space Flight.

BC Transistor | BC Datasheet

Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. Amplifier modules like Audio amplifiers, signal Amplifier etc.

BC has a gain value of to ; this value determines the amplification capacity of the transistor. BC is used in common emitter configuration for amplifiers. The DC current gain varies in range to For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves.

  INSTRUMENTATION AND PROCESS CONTROL BY TERRY BARTELT PDF

Transistor BC558

When uses as an Bc558 the DC current gain of the Transistor can be calculated by using the below formulae. Skip to main content.

It is used in switching and amplifier applications. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. BC is a general purpose PNP transistor. A resistor is always added in series with base pin to limit the b558 current. The input signal at base is amplified and taken at the emitter. BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

Where an input signal of low voltage is amplified switched to satasheet voltages t0 drive loads like speakers. Arduino based GPS receiver.

Submitted by admin on 26 March