Allen-Bradley, Rockwell Automation, and PowerFlex are registered trademarks of PowerFlex 4M Adjustable Frequency Drive FRN – User Manual. I/O Wiring. PowerFlex 4M Quick Start Guide. Display. Parameter Group. First Shown when drive powered up. Display Group. (View Only). Basic Program Group. View and Download ALLEN BRADLEY PowerFlex 4M user manual online. FRN 1 Series, FRN 2 Series, Adjustable Frequency AC Drive. PowerFlex 4M.
|Published (Last):||22 November 2017|
|PDF File Size:||19.64 Mb|
|ePub File Size:||1.30 Mb|
|Price:||Free* [*Free Regsitration Required]|
Installations on a public low voltage power network may require additional external harmonic mitigation. To print the manual completely, please, download it.
Page 97 Catalog Number: All poeerflex must be powered up for the analog signal to be read correctly. Included is a listing and description of drive faults with possible solutions, when applicable. Parameters marked 32 bit will have two parameter numbers when using RS communications and programming software.
Solution Partners Powerfkex Integrators. Our Integrated Architecture Solutions provide the foundation to drive plantwide optimization efficiently and effectively, enabling you to respond competitively to the economy and changes in consumer demand. Any wire chosen must have a minimum insulation thickness of 15 mils and should not have large variations in insulation concentricity.
PowerFlex 4M AC Drives
Sets the frequency at which the drive will not operate. When this bit is a 0 the drive will stop.
Comments to this Manuals Your Name. Poeerflex 22 When the AC line is removed, there will be a loss of any inherent regenerative braking effect that might be present – the motor will coast to a stop. Page 76 Failure has been detected in the 1. HERTZ that group will flash. DC Bus Inductor not connected. See Appendix B for details.
22F-A4P2N – – Allen Bradley – PowerFlex 4M kW (1 Hp) AC Drive
Troubleshooting Chapter Troubleshooting Chapter 4 provides information to guide you in troubleshooting the PowerFlex 4M majual. Don’t have an account? Additional software products are available from Rockwell Software. Page 78 [Digital Inx Select]. Appendix B Refer to for accessory ordering information. Page 16 Some local codes may require redundant ground connections.
ALLEN BRADLEY PowerFlex 4M User Manual
See Appendix B for ordering information. Power must be applied to the drive to perform the following start-up procedures. In addition, some Modbus braley are supported to allow simple networking. Tighten the screw to keep it in place. Page 40 Start Up Notes: Advanced Sllen Group Values Default Page 1 foot. Product Certifications Certifications apply when product is marked.
Page 32 Keep wire length as short as possible between the enclosure entry point and the EMI filter.
Press and hold in the tabs on each side of the cover. Brwdley 33 Installations on a public low voltage power network may require additional external harmonic mitigation. Ac Supply Source Considerations 2.
Information on reading register address clarified. Chapter Troubleshooting Chapter 4 provides information to guide you in troubleshooting the PowerFlex 4M drive.
ProposalWorks — Build complete quotes and proposals. Motor Ground The motor ground must be connected to one of the ground terminals on the drive. Page 3 Description for bits 6, 7, and 15 of register address updated. Page 65 [Maximum Freq]. Guidelines on standard RS wiring practices added.
Read the General Precautions yser before proceeding. Based on Drive Rating Display: Windows 98, ME, NT 4. Refer to parameter A Brake Level]. Values Default Drive Rated Amps 0. Page 61 Sets the frequency at which the drive will not operate. Page 88 Alternative resistors may be used, however care must be taken when making a selection.
Learn how the information from our portfolio of Intelligent Motor Control can position you to make better operating decisions, improve system performance, and gain operation efficiencies.
In addition, installing a properly sized dynamic brake resistor will provide equal or better performance in most cases. When using a Manual Self-Protected Type E Combination Motor Controller, the drive must be installed in a ventilated or non-ventilated enclosure with the minimum volume specified in this column.