4011BE DATASHEET PDF

4011BE DATASHEET PDF

Data sheet acquired from Harris Semiconductor. SCHSD – Revised September The CDB, CDB, and CDB types. BE Datasheet, BE PDF, BE Data sheet, BE manual, BE pdf, BE, datenblatt, Electronics BE, alldatasheet, free, datasheet. STMicroelectronics HCFBE: available from 8 distributors. Explore STMicroelectronics on Octopart: the fastest source for datasheets, pricing, specs and.

Author: Mazukree Shaktijas
Country: Bahamas
Language: English (Spanish)
Genre: Technology
Published (Last): 18 March 2006
Pages: 308
PDF File Size: 14.15 Mb
ePub File Size: 17.39 Mb
ISBN: 937-4-36037-191-1
Downloads: 77214
Price: Free* [*Free Regsitration Required]
Uploader: Taule

BE datasheet & applicatoin notes – Datasheet Archive

Any gate type may be tested with two switches, two pulldown resistors, and an LED to indicate output status. In the breadboard illustration, I show all the top inputs connected to V DDand all the bottom inputs of the unused gates connected to ground. Shown here is my own rendition of what any datasheet shows:.

However, the presence of those extra switches and LEDs make it very convenient to expand the circuit and help make the circuit layout both clean and compact. It introduces the concept of frequency domain aliasing and describes Additional Improvement An improvement you might want to make to this circuit is to assign a couple of LEDs to indicate input status, in addition to the one LED assigned to indicate the output.

This way, the input will not be susceptible to stray static voltages. This makes operation a little more interesting to observe, and has the further benefit of indicating if a switch fails to close or open by showing the true input signal to the gate, rather than forcing you to infer input status from switch position: You May Also Like: It is highly recommended that you have a datasheet for the chip available when you build your circuit.

  2003 IMPALA OWNERS MANUAL PDF

This was done merely because those power supply rail holes were closer and did not require long jumper wires! This makes operation a little more interesting to observe, and has the further benefit of indicating if a switch fails to close or open by showing the true input signal to the gate, rather than forcing you to infer input status from switch position:.

Note how all inputs of the unused gates inside the chip are connected either to V DD or ground. This is not a mistake, but an act of intentional design. Draw a truth table on a piece of paper like this: Shown here is my own rendition of what any datasheet shows: At worst, this could lead to damage of the chip. datazheet

Introduction to Capacitive Touch Sensing In this article, we will take a detailed but not too detailed look at the electrical principles that allow us to detect the presence of a Quote of the day.

Published under the terms and conditions of the Design Science License.

BE pdf Datasheet P1 Part Num IC-ON-LINE

Draw a truth table on a piece of paper like this:. As you can imagine, this breadboard circuit is not limited to testing NAND gates.

  MAESTRO SECRETO LAVAGNINI PDF

An improvement you might want to make to this circuit is to assign a couple of LEDs to indicate input status, in addition to the one LED assigned to indicate the output. Please note that none of the unused gate outputs have been connected to V DD or ground, and for good reason!

Basic Gate Function

This technical brief explains two distinct types of electromagnetic interference. Who cares what signals they receive, if we are not doing anything with their outputs? Instead, its upper P-channel output transistor would be turned on in vain, sourcing maximum current to a nonexistent load.

Lessons In Electric CircuitsVolume 4, chapter 3: Even if you already know what a NAND gate truth table looks like, this is a good exercise in experimentation: At best it means excessive power consumption.

Digital logic circuitry does not make use of datasyeet power supplies as op-amps do.

Like op-amp circuits, though, ground is still the implicit point of reference for all voltage measurements. This would very likely damage the gate!